diff options
Diffstat (limited to 'mbed/hal/i2c_api.h')
| -rw-r--r-- | mbed/hal/i2c_api.h | 248 |
1 files changed, 248 insertions, 0 deletions
diff --git a/mbed/hal/i2c_api.h b/mbed/hal/i2c_api.h new file mode 100644 index 0000000..1f01f52 --- /dev/null +++ b/mbed/hal/i2c_api.h @@ -0,0 +1,248 @@ +
+/** \addtogroup hal */
+/** @{*/
+/* mbed Microcontroller Library
+ * Copyright (c) 2006-2015 ARM Limited
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+#ifndef MBED_I2C_API_H
+#define MBED_I2C_API_H
+
+#include "device.h"
+#include "hal/buffer.h"
+
+#if DEVICE_I2C_ASYNCH
+#include "hal/dma_api.h"
+#endif
+
+#if DEVICE_I2C
+
+/**
+ * @defgroup hal_I2CEvents I2C Events Macros
+ *
+ * @{
+ */
+#define I2C_EVENT_ERROR (1 << 1)
+#define I2C_EVENT_ERROR_NO_SLAVE (1 << 2)
+#define I2C_EVENT_TRANSFER_COMPLETE (1 << 3)
+#define I2C_EVENT_TRANSFER_EARLY_NACK (1 << 4)
+#define I2C_EVENT_ALL (I2C_EVENT_ERROR | I2C_EVENT_TRANSFER_COMPLETE | I2C_EVENT_ERROR_NO_SLAVE | I2C_EVENT_TRANSFER_EARLY_NACK)
+
+/**@}*/
+
+#if DEVICE_I2C_ASYNCH
+/** Asynch I2C HAL structure
+ */
+typedef struct {
+ struct i2c_s i2c; /**< Target specific I2C structure */
+ struct buffer_s tx_buff; /**< Tx buffer */
+ struct buffer_s rx_buff; /**< Rx buffer */
+} i2c_t;
+
+#else
+/** Non-asynch I2C HAL structure
+ */
+typedef struct i2c_s i2c_t;
+
+#endif
+
+enum {
+ I2C_ERROR_NO_SLAVE = -1,
+ I2C_ERROR_BUS_BUSY = -2
+};
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+ * \defgroup hal_GeneralI2C I2C Configuration Functions
+ * @{
+ */
+
+/** Initialize the I2C peripheral. It sets the default parameters for I2C
+ * peripheral, and configures its specifieds pins.
+ *
+ * @param obj The I2C object
+ * @param sda The sda pin
+ * @param scl The scl pin
+ */
+void i2c_init(i2c_t *obj, PinName sda, PinName scl);
+
+/** Configure the I2C frequency
+ *
+ * @param obj The I2C object
+ * @param hz Frequency in Hz
+ */
+void i2c_frequency(i2c_t *obj, int hz);
+
+/** Send START command
+ *
+ * @param obj The I2C object
+ */
+int i2c_start(i2c_t *obj);
+
+/** Send STOP command
+ *
+ * @param obj The I2C object
+ */
+int i2c_stop(i2c_t *obj);
+
+/** Blocking reading data
+ *
+ * @param obj The I2C object
+ * @param address 7-bit address (last bit is 1)
+ * @param data The buffer for receiving
+ * @param length Number of bytes to read
+ * @param stop Stop to be generated after the transfer is done
+ * @return Number of read bytes
+ */
+int i2c_read(i2c_t *obj, int address, char *data, int length, int stop);
+
+/** Blocking sending data
+ *
+ * @param obj The I2C object
+ * @param address 7-bit address (last bit is 0)
+ * @param data The buffer for sending
+ * @param length Number of bytes to write
+ * @param stop Stop to be generated after the transfer is done
+ * @return
+ * zero or non-zero - Number of written bytes
+ * negative - I2C_ERROR_XXX status
+ */
+int i2c_write(i2c_t *obj, int address, const char *data, int length, int stop);
+
+/** Reset I2C peripheral. TODO: The action here. Most of the implementation sends stop()
+ *
+ * @param obj The I2C object
+ */
+void i2c_reset(i2c_t *obj);
+
+/** Read one byte
+ *
+ * @param obj The I2C object
+ * @param last Acknoledge
+ * @return The read byte
+ */
+int i2c_byte_read(i2c_t *obj, int last);
+
+/** Write one byte
+ *
+ * @param obj The I2C object
+ * @param data Byte to be written
+ * @return 0 if NAK was received, 1 if ACK was received, 2 for timeout.
+ */
+int i2c_byte_write(i2c_t *obj, int data);
+
+/**@}*/
+
+#if DEVICE_I2CSLAVE
+
+/**
+ * \defgroup SynchI2C Synchronous I2C Hardware Abstraction Layer for slave
+ * @{
+ */
+
+/** Configure I2C as slave or master.
+ * @param obj The I2C object
+ * @return non-zero if a value is available
+ */
+void i2c_slave_mode(i2c_t *obj, int enable_slave);
+
+/** Check to see if the I2C slave has been addressed.
+ * @param obj The I2C object
+ * @return The status - 1 - read addresses, 2 - write to all slaves,
+ * 3 write addressed, 0 - the slave has not been addressed
+ */
+int i2c_slave_receive(i2c_t *obj);
+
+/** Configure I2C as slave or master.
+ * @param obj The I2C object
+ * @return non-zero if a value is available
+ */
+int i2c_slave_read(i2c_t *obj, char *data, int length);
+
+/** Configure I2C as slave or master.
+ * @param obj The I2C object
+ * @return non-zero if a value is available
+ */
+int i2c_slave_write(i2c_t *obj, const char *data, int length);
+
+/** Configure I2C address.
+ * @param obj The I2C object
+ * @param idx Currently not used
+ * @param address The address to be set
+ * @param mask Currently not used
+ */
+void i2c_slave_address(i2c_t *obj, int idx, uint32_t address, uint32_t mask);
+
+#endif
+
+/**@}*/
+
+#if DEVICE_I2C_ASYNCH
+
+/**
+ * \defgroup hal_AsynchI2C Asynchronous I2C Hardware Abstraction Layer
+ * @{
+ */
+
+/** Start I2C asynchronous transfer
+ *
+ * @param obj The I2C object
+ * @param tx The transmit buffer
+ * @param tx_length The number of bytes to transmit
+ * @param rx The receive buffer
+ * @param rx_length The number of bytes to receive
+ * @param address The address to be set - 7bit or 9bit
+ * @param stop If true, stop will be generated after the transfer is done
+ * @param handler The I2C IRQ handler to be set
+ * @param hint DMA hint usage
+ */
+void i2c_transfer_asynch(i2c_t *obj, const void *tx, size_t tx_length, void *rx, size_t rx_length, uint32_t address, uint32_t stop, uint32_t handler, uint32_t event, DMAUsage hint);
+
+/** The asynchronous IRQ handler
+ *
+ * @param obj The I2C object which holds the transfer information
+ * @return Event flags if a transfer termination condition was met, otherwise return 0.
+ */
+uint32_t i2c_irq_handler_asynch(i2c_t *obj);
+
+/** Attempts to determine if the I2C peripheral is already in use
+ *
+ * @param obj The I2C object
+ * @return Non-zero if the I2C module is active or zero if it is not
+ */
+uint8_t i2c_active(i2c_t *obj);
+
+/** Abort asynchronous transfer
+ *
+ * This function does not perform any check - that should happen in upper layers.
+ * @param obj The I2C object
+ */
+void i2c_abort_asynch(i2c_t *obj);
+
+#endif
+
+/**@}*/
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif
+
+#endif
+
+/** @}*/
|